/*
	UIDIGI Configuration source file
	Version 1.9 BETA 3 20040101
	Written by Marco Savegnago IW3FQG

2005/12/01: Configured for 'The New-N Paradigm', N=2, by Ron Stordahl,
 N5IN.  See InfoText,UIDigiCall,UIFloodCall,UITracecall,UIFLOODOptions,
 UITRACEOptions,UIOnly,BeaconNInterval,BeaconNText,PPersistance & Slottime.
 http://dxspots.com/FIX14439_UIDIGI-ROM.html
*/
//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// Set the digipeater ax.25 address callsign (SSID allowed)
// Up to 6 characters+SSID
// Digicall [t]

DigipeaterCallsign = VK2RGN-1

//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// Set the digipeater address alias
// Up to 6 characters (NO SSID)
// DIGIAlias [t]

DigipeaterAlias = GLBURN

//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// Digipeater Info Text up to 80 char
// Info [t]
// Note: W2,MNn applicable in section MN.  Change to match your section
//
//         12345678101234567820123456783012345678401234567850123456786012345678701234567880

InfoText = VK2RGN-1 Supports WIDEn-n and NSWn-n.   For more information see vk2.aprs.net.au

//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// Path used when SSID routing is used (Up to 8 hops)
// (Direction) Path
// xpath [path]

NorthPath =

SouthPath =

EastPath =

WestPath =

//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// BudList Calls (up to 8 calls, default none)
// All SSID's of base call will be ignored
// BUdlist [calls]

BudList = NOCALL
//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// UI Generic Calls (up to 8)
// Calls recognized by digi to repeat
// Default (RELAY, WIDE, TRACE)
// Uidigi [calls]

UIDigiCall = WIDE1-1,WIDE3-3,WIDE4-4,WIDE5-5,WIDE6-6,WIDE7-7,INETNF

//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// UI Flood Call (up to 6 characters) - Set this for your State or ARRL Section
// Default (WIDE)
// UIFlood [call]

UIFloodCall = NSW

//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// UI Trace Call (up to 6 characters)
// Default (TRACE)
// UITrace [call]

UITraceCall = WIDE

//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// Txdelay (default 30 = 300)
// range 1-255 x10ms
// TXdelay [n]

TxDelay = 35

//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// Fullduplex (default 0)
// Enables (1) or Disables (0)
// NO COMMAND FROM CONSOLE

FullDuplex = 0

//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// PPErsistence (default 64)
// range 1-255
// Parameter fo channel access timing
// PErsistance [n]

PPersistance = 64

//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// Slottime (default 10)
// range 1-255 x100ms
// SLottime [n]

SlotTime = 15

//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// Frack   (default 5)
// range 1-15
// Frack [n]

Frack = 5

//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// Maxframe (default 4)
// range 1-7
// MAxframe [n]

Maxframe = 4

//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// Retry (default 10)
// range 0-127
// RETry [n]

Retry = 10

//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// RespTime 2 (default 100)
// range 0-6000 ms
// RESPtime [n]

RespTime = 100

//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// Link Check (default 18000)
// range 0-65535 ms
// CHeck [n]

LinkCheck = 18000

//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// Duplicate Packet Suppression Interval second (default 28)
// range 0-180 seconds
// UICheck [n]

DuplicateSuppression = 32

//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// Loop Packet Suppression Interval Mask (default 3)
//  0x01 = Do not repeat frame with source address equal to digipeater call or alias
//  0x02 = Do not repeat frame with the digipeater call in the already digipeated via list
// range 0-3
// UILoop [n]

LoopSuppression = 3

//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// Treat different SSID in destination call (default 1)
// Enables (1) or Disables (0) UISSID digipeating mode
// Used for SSID Directional routing
// UISsid [n]

HandleUISSID = 0

//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// Reply to Query (default 1)
// Enables (1) or Disables (0) ?APRS? response query
// UIQuery [n]

ReplyToQuery = 1

//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// UIFLOOD Algorithm flag (default 4)
//  Bit 0: FLOODCALLn-0 will be repeated
//  Bit 1: Insert callsign before FLOODCALLn-N
//  BIT 2: Put has been repeated flag on FLOODCALLn-0
//  BIT 3: Make call substitution on FLOODCALLn-0
//
// NOTE:  You must use the October 4, 2005 or later version of the DOS
// configuration program UIDGCFG.exe or the 32 bit version UIDGCFG32.exe,
// otherwise if you set UIFLOODOptions=4 (offset X’344 in the binary) 
// and UITRACEOptions=2 (offset X’346’ in the binary) as desired, both
// options are forced to 4 in the generated binary!!  This new version
// of the DOS configuration program, which corrects the problem, can be
// obtained in the files section of the UIDIGI Yahoo Group in the
// UIDIGI 1.9 folder.  The version in the archive UIDG19B3.zip is the
// defective version.  The 32 bit version of the configuration program,
// UIDGCFG32.exe, found in the archive uitools32.zip in the UIDIGI 1.9
// folder, generates the correct binary.   
//
// UIFLDfl [n]

UIFLOODOptions = 4

//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// UITRACE Algorithm flag (default 2)
//  Bit 0: TRACECALLn-0 will be repeated
//  BIT 1: Put has been repeated flag on TRACECALLn-0
//  BIT 2: Make call substitution on TRACECALLn-0
//  This is located at offset x'346' in the image.
// 
// UITRFl [n]

UITRACEOptions = 2

//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// Make call substitution when repeat frames addressed to UIDIGI Callsign
//  default (1)
// Enables (1) or Disables (0) UIDIGI callsign substituion for UIDIGI calls
// UIDCsb [n]

UIDIGICallSubstitution = 1

//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// Preempt calls (default none)
// see docs

PreemptCalls = 

//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// Preempt add (default none)
// see docs

PreemptAdd = 

//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// Preempte Digipeater (default 0)
// see docs

PreemptedDigipeat = 0

//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// Don't change SSID (decrement) to UI Message (frame with info that start 
// with char '~' default (1) 
// 0 disables
// range 0-1
// UIMessage [n]

UIMessage = 1

//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// Process only UI Frame (default 0)
// Enable processing of UI frame only 
// 0 disables
// range 0-1
// UIOnly [n]

UIOnly = 0

//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// PID of processed frames (default 240)
// Enable frame filtering algorithm base on PID of frame
// 0 disables
// range 0-255
// UIPid [n]

UIPID = 240

//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// Sysop Password up to 80 char
// NO CONNAMD FROM LOCAL CONSOLE

SysopPassword = mtgreyaprs

//              1234567810123456782012345678301234567840
//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// Beacon x interval Seconds
// default 1 = 600
// default 2 = 1800
// default 3 = 3600
// range 0-65535 seconds
// BEacon [x] [n]

Beacon1Interval = 900

Beacon2Interval = 1740

Beacon3Interval = 610

//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// Beacon x offset (default 0)
// range 0-65535 seconds
// BEACONOffset [x] [n]

Beacon1Offset = 0

Beacon2Offset = 0

Beacon3Offset = 0


//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// Digipeater Beacon x Text up to 70 char
// see APRS reference doc for layout
// BText [n] [t]
// Note: W2,MNn applicable in section MN.  Change to match your section
//
//            1234567810123456782012345678301234567840123456785012345678601234567870

Beacon1Text = !3445.39SS14941.29E#PHG4630/W2 Digi   Goulburn

Beacon2Text = !3445.39SS14941.29E#PHG4630/W2 Digi   Goulburn

Beacon3Text = ;146.825- *111111z3445.  S/14945.  Er R50k  

//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// Destination ax.25 address of beacon (6 characters + SSID)
// See APRS working group documentation APNUnn
// UNproto [t]

BeaconDestination = APNU19

//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// AX.25 Beacon x path (up to 8 hops)
// Path that Beacon x will be sent out with
// Bdl [x] [path]

Beacon1Path = 

Beacon2Path = WIDE2-2

Beacon3Path = NOGATE

AuxPath = WIDE2-2  

//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// Destination ax.25 address of aux input device string
// Up to 6 characters + SSID

AuxDestination = TLM

//-----------------------------------------------------------------------
//-----------------------------------------------------------------------
// Aux Beacon interval (default 0)
// Sets the interval for the beacon of aux input data 
// AUXRate [n]

AuxRate = 60

//-----------------------------------------------------------------------
//-----------------------------------------------------------------------